CREATIVE GIGAWORKS S750 MANUAL PDF
Get Creative Creative GigaWorks S Technology Speaker System User Manual. Get all Creative manuals!. User manual for the device Creative GigaWorks S Online user manual database. Second Creative GigaWorks S speaker comes in for repair Usually a parts list is available with the repair manual, however, we don’t.
|Published (Last):||9 October 2014|
|PDF File Size:||10.12 Mb|
|ePub File Size:||6.86 Mb|
|Price:||Free* [*Free Regsitration Required]|
Show posts by this member only Post 9. Haatdragende of gewelddadige inhoud Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke gigawworks tot gevolg kan hebben. This product conforms to the following Council Directive: Oh, I just had another set of these speakers turn up. B] see why i wanted to restore it so badly: Don’t see a manual you are looking for? Hi everyone, i have a megaworks THX and was playing with it awhile ago.
If you do not hear sound from your new speaker, keep.
Important safety instructions | CREATIVE GigaWorks S User Manual | Page 2 / 12 | Original mode
And when I got the power board back, it’s missing some components, I guess the guy didn’t put them back. Try using higher wattage parts, plus check D16, R39, C30 and C58 replace all of them if necessary.
The bare copper areas you mention, and I hope there are few, can be coated after you have completed work in those areas. With the Upmix feature, the 5. You can read more about it here: Notice the bits of residual degraded glue sticking to some of those components on the right.
I got this problem too, they came off very easily. The T2 info should be on the transformer itself. January December Any background noise you hear is not due to a fault in the speaker system.
There seams to be short-circuit on these lines. Our goal is to provide you with a quick access to the content of the user manual for Creative GigaWorks S That’s an extra wire in the through hole Did you managed to fully revive the unit?
The connector also has an arrow marking point to the number one pin. Uw handleiding is per email verstuurd. The following sections contain notices for various countries:.
Lex, u accept repair faulty speaker? Creative GigaWorks S user manual. Time to assemble everything together.
Heating up electrolytic capacitors will increase its capacitance, thus “restores” some capacitance to allow the power circuits to continue to function. For those capacitors after the voltage regulators, any low impedance capacitors will do.
Also, since the voltages delivered by these connectors are very small, some glue on the pins or inside the connectors may be preventing the sound, or that the connectors are not well seated because of glue or other interference.
Feb 22 Likewise if the C7 blue capacitor is intact and does not show a short I would also leave it alone for now. In your opinion creativr they also need replacing? The diode is pretty much run-of-the-mill 1N, which is a very common diode. Unless there is obvious evidence that cteative components nearby may be the cause, I would assume a faulty connection when C62 replacement or glue remnants caused the short, and clean up the area very carefully while checking for a possible defect on the board.
I still have another question, since I haven’t replaced other small caps yet.
Important safety instructions – CREATIVE GigaWorks S750 User Manual
Those degraded glue are not hot glue. What was the desoldering tool used?
Can you help me out there? Before we go any further, you should not majual to work on this project without having a thorough understanding of electricity and the extremely dangerous hazard to your life if you do not observe the proper safety precautions to protect yourself at all times. I know next to nothing about what is what or how to test things, I only know if something doesn’t look right replace it. The diode is blown to beyond recognition very little left of the markings.
Using multiple inputs | CREATIVE GigaWorks S User Manual | Page 12 / 12 | Original mode
If you do not want to desolder the board off which is a lot of hard and difficult work, particularly since this is double sided PCB then try usuing a thin long flat head screwdriver plus very fine but strong tweezers to remove those glue. Feb 5gigaworkx Extreme care should be observed when removing and installing components, especially the caps with the feed through connections.
Nov 4 You may try finding someone with electronics repair experience gigaworka.
The speakers are connected properly. Many people prefer to read the documents not on the screen, but in the printed version. I don’t know the difference betwin ceramic and lytics. How do you remove those glue? Seems Panasonic decided to quit producing snap-ins. Subwoofer problem The main reason the subwoofer sounded broken and distorted was that all 3 voice coils inside the 8″ woofer were damaged.
If so, how is that done? These are components mostly capacitors and a blown diode that were pulled out. Quite often very time consuming.